Z Mill Floor Operator

4 weeks ago

Ghent, United States North American Stainless Full time
Job DescriptionJob Description

The Z-Mill operator is responsible for all of the operating functions of the Z-Mill listed below. Operation of the mill must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All functions of the unit are to be carried out as described in the work instructions.

DUTIES

1. Check coil to be run for proper identification which corresponds to the program.
2. Load coil onto either the pay off reel or the tension reel.
3. Feed coil through mill to opposite tension reel.
4. Remove interleaving paper or plastic as required.
5. Load all information into the computer for rolling parameters.
6. Insert work rolls into the mill and following the rolling schedule, run the first pass at prescribed speeds according to work instructions. Periodic gauge referencing must be made during rolling. Adjust as necessary.
7. Stop the mill at prescribed intervals as indicated in work instructions and inspect both the top and the bottom face of the strip for rolling defects. Change any rolls, hose wiper etc. to insure the quality of the strip.
8. Insert paper into the coil during last pass.
9. Once coil is completed, remove from tension reel, band and identify per work instructions.
10. Enter completed coil data into the AS-400 system as well as note abnormalities (AQNS).
SUPPLEMENTAL JOB FUNCTIONS:
1. Coordinate movement with the crane operator for coil and roll movements.
2. Communicate roll necessities with roll grinding department.
3. Change rolls in the mill box.
4. Grease mill unit as specified in work instructions.
5. Perform daily checks as specified in appropriate checklists.
6. Utilize all diagnostics as necessary.
7. Calculate rolling schedules and tensions if necessary.
8. Utilize paper interleaving as per work instructions.
9. Perform maintenance work as assigned.
10. Maintain proper housekeeping throughout the entire work area.
11. Work swing shift

QUALIFICATIONS

MINIMUM EDUCATION, SKILLS AND EXPERIENCE:

High School Degree or Equivalent (GED)

PHYSICAL ABILITIES REQUIRED:

1. Mobility: Stand (stationary) - 10%, stand/walk - 20%, walking - 10%, sitting - 60%.

2. Strength and Agility: Lifting up to 70 lbs and carrying over a distance of 10 feet, and pushing or pulling 100 lbs. Occasional climbing, bending, twisting, kneeling, turning, stooping, crouching, and balancing

3. Mobility in Plant.

4. Ability to lift at least 50 lbs.

5. Visual ability with or without correction.

6. Communication ablitites.

7. Ability to work rotating shift ( rotating from days to nights on a weekly or bi-weekly schedule).

HEALTH AND SAFETY

1. Work in compliance with the Occupational Health and Safety Act and regulations.

2. Follow Company safety rules.

3. Report the absence of or defect in any protective equipment or clothing to the Supervisor or Manager immediately.

4. Use or wear the equipment, protective devices or clothing that is required to be used or worn:

· Safety shoes

  • HM Floor Operator

    1 month ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThe position of Mill Floor Operator is responsible for theoperation of all Furnace Delivery, Roughing Mill, Finishing Mill,down coiler and plate line equipment at the floor level in orderto obtain the proper levels of quality and productivity. Thisposition is also responsible for monitoring the rolling processand the auxiliary...

  • HM Floor Operator

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThe position of Mill Floor Operator is responsible for theoperation of all Furnace Delivery, Roughing Mill, Finishing Mill,down coiler and plate line equipment at the floor level in orderto obtain the proper levels of quality and productivity. Thisposition is also responsible for monitoring the rolling processand the auxiliary...

  • RG Operator

    3 months ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThe Z-Mill Roll Grinder Operator is responsible for all operating functions of the roll grinding unit listed below. Operation of the Roll Grinding equipment must be understood fully with a focus on utilizing the equipment to achieve productivity and quality goals as outlined in our quality systeESSENTIAL JOB FUNCTIONS:Coordinate...

  • RG Operator

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThe Z-Mill Roll Grinder Operator is responsible for all operating functions of the roll grinding unit listed below. Operation of the Roll Grinding equipment must be understood fully with a focus on utilizing the equipment to achieve productivity and quality goals as outlined in our quality systeESSENTIAL JOB FUNCTIONS:Coordinate...

  • SKP Floor Operator

    3 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThe Skin Pass 2 operator is responsible for all of the operating functions of the Skin Pass 2 Mill listed below. Operation of the mill must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All functions of the unit are to be carried...

  • Mech Mtn Eng Z-Mills

    2 months ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:This position is responsible for providing professional Mechanical Engineering service and technical support to Maintenance and Operation departments for the re- design, modification, re-engineering and retro-fitting of machinery and equipment to improve quality and productivity.ESSENTIAL JOB FUNCTIONS:...

  • Mech Mtn Eng Z-Mills

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:This position is responsible for providing professional Mechanical Engineering service and technical support to Maintenance and Operation departments for the re- design, modification, re-engineering and retro-fitting of machinery and equipment to improve quality and productivity.ESSENTIAL JOB FUNCTIONS:...

  • EAF Floor Operator

    1 month ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:The position of Electric Arc Furnace floor Operator is responsible for all operating functions of the Electric Arc Furnace as listed below.Complete understanding of EAF operations with the objective of utilizing the equipment to meet all of the quality and productivity standards as defined in the quality...

  • EAF Floor Operator

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:The position of Electric Arc Furnace floor Operator is responsible for all operating functions of the Electric Arc Furnace as listed below.Complete understanding of EAF operations with the objective of utilizing the equipment to meet all of the quality and productivity standards as defined in the quality...

  • ZM Process Engineer

    2 weeks ago

    Ghent, United States North American Stainless Full time

    GENERAL JOB DESCRIPTION:This position is responsible for providing engineering service and technical support to the Cold Mill operations with respect to enhancing productivity, improving yield and reducing cost. Supports the operations team, by recommending areas of improvement, supporting floor operations, and solving day-to-day issues related to yield and...

  • ZM Process Engineer

    3 weeks ago

    Ghent, United States North American Stainless Full time

    GENERAL JOB DESCRIPTION: This position is responsible for providing engineering service and technical support to the Cold Mill operations with respect to enhancing productivity, improving yield and reducing cost. Supports the operations team, by recommending areas of improvement, supporting floor operations, and solving day-to-day issues related to yield and...

  • ZM Process Engineer

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:This position is responsible for providing engineering service and technical support to the Cold Mill operations with respect to enhancing productivity, improving yield and reducing cost. Supports the operations team, by recommending areas of improvement, supporting floor operations, and solving...

  • Stand Assembly Operator

    2 months ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThis position of the Long Product Hot Rolling Mill Stand Assembly Operator is responsible for all operating functions as listed below. Proper assembling of the roll units must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals in a safe manner.DUTIES1.Communication...

  • Stand Assembly Operator

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionThis position of the Long Product Hot Rolling Mill Stand Assembly Operator is responsible for all operating functions as listed below. Proper assembling of the roll units must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals in a safe manner.DUTIES1.Communication...

  • Compactor/Stacker Operator

    2 months ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:Perform a number of duties in the continuous mill that provide the mill the best opportunity to operate at an efficient level. Be able to perform the exit operator's duties at an adequate level during the absence of any of the continuous mill operators.ESSENTIAL JOB FUNCTIONS: CompactorSAFETY: provide...

  • Compactor/Stacker Operator

    4 weeks ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob DescriptionGENERAL JOB DESCRIPTION:Perform a number of duties in the continuous mill that provide the mill the best opportunity to operate at an efficient level. Be able to perform the exit operator's duties at an adequate level during the absence of any of the continuous mill operators.ESSENTIAL JOB FUNCTIONS: CompactorSAFETY: provide...

  • Cold Mill Crane Operator

    2 weeks ago

    Ghent, United States North American Stainless Full time

    Company Overview North American Stainless is the largest fully integrated stainless steel producer in the United States. North American Stainless was founded in April 1990 with the mission to create the most appropriate high-performance materials for each application, thus contributing to the progress and quality of life of a sustainable society. Our...

  • Cold Mill Crane Operator

    2 weeks ago

    Ghent, United States North American Stainless Full time

    Company OverviewNorth American Stainless is the largest fully integrated stainless steel producer in the United States. North American Stainless was founded in April 1990 with the mission to create the most appropriate high-performance materials for each application, thus contributing to the progress and quality of life of a sustainable society. Our...

  • Billet Crane Operator

    2 weeks ago

    Ghent, Kentucky, United States North American Stainless Full time

    GENRAL DESCRIPTION: This position of Billet Crane Operator is responsible for all operating functions as listed below. Running the crane must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system.ESSENTIAL JOB FUNCTIONS: Make sure slabs are identified properly. Pile...

  • CM Crane Operator

    2 months ago

    Ghent, United States North American Stainless Full time

    Job DescriptionJob Description all operating function of all cranes located in the Cold Mill. Operation of the crane must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as outlined. Know potential hazards for each task by...