Press Operator

1 month ago

Grand Rapids, United States Boyd Full time

Job Description

Essential Duties Include:

Read and understand “Change Spec. Card Procedure” Read and understand “Non-Conforming Product Procedure” Get magnets from magnet board that contains the work order information for production Locate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructions Determine and obtain the correct tool for the job identified on the Spec. Card from the tooling rack Remove tooling from box, attach bearer blocks and slide into tooling station Set the machine for the appropriate job Retain Supplier raw material tag with lot # and run # information along with “Approved for Use” tags on separate sheet of paper (if only using partial material and retuning excess material do not retain tag, just record part #, lot # and run # on sheet) Complete “Sign-off Check List” (if operator has less than 1-year experience, needs sign-off from experienced operator with over 1 year experience) Print out (core tags or box tags) along with 1st piece and last piece labels with correct information, Make sure the right material is used where needed, to the proper side of the liner and in the right orientation Place material in machine. Feed it through the fife guide and adjust it for center run. Place adhesive in machine and line-up with materials so that they are even with each other Start machine, adjust tension and alignment as needed Pass the material through to the die cutting station Remove any waste or air-injection from the tool Adjust nip-roller speed for proper speed and dimensions of part Verify part to print and or mylar and record dimensions Retain first approved piece and place label on back side Complete In-Process check sheet during the run. Complete End-of-Run sign off confirming the required parts were produced. Retain last approved piece and label back side Maintain a clean and safe work area, cleaning floor, machine, work area at end of each job and at end of shift Cut cores for particular jobs when needed. Obtain boxes and materials necessary for job Operate production equipment to produce good, quality product in an efficient/quality-oriented manner. Makes suggestions for ways to improve production process Works with sales and estimating to test/run samples for new product introduction Makes sure product being produced matches the spec card and the degree of quality needed (tolerances Updates spec card for future runs when process is changed Observe machine operation to detect workpiece defects or machine malfunctions; adjust machines as necessary. Change worn machine accessories such as cutting tools and brushes, using hand tools. Perform minor machine maintenance, such as oiling or cleaning machines, changing filters or adding lubricant to the Rotary press when necessary. Notify supervisors when major service is required. Other duties as assigned.

Education:

High school diploma or equivalent

Requirements

Essential Duties Include:

Read and understand “Change Spec. Card Procedure” Read and understand “Non-Conforming Product Procedure” Get magnets from magnet board that contains the work order information for production Locate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructions Determine and obtain the correct tool for the job identified on the Spec. Card from the tooling rack Remove tooling from box, attach bearer blocks and slide into tooling station Set the machine for the appropriate job Retain Supplier raw material tag with lot # and run # information along with “Approved for Use” tags on separate sheet of paper (if only using partial material and retuning excess material do not retain tag, just record part #, lot # and run # on sheet) Complete “Sign-off Check List” (if operator has less than 1-year experience, needs sign-off from experienced operator with over 1 year experience) Print out (core tags or box tags) along with 1st piece and last piece labels with correct information, Make sure the right material is used where needed, to the proper side of the liner and in the right orientation Place material in machine. Feed it through the fife guide and adjust it for center run. Place adhesive in machine and line-up with materials so that they are even with each other Start machine, adjust tension and alignment as needed Pass the material through to the die cutting station Remove any waste or air-injection from the tool Adjust nip-roller speed for proper speed and dimensions of part Verify part to print and or mylar and record dimensions Retain first approved piece and place label on back side Complete In-Process check sheet during the run. Complete End-of-Run sign off confirming the required parts were produced. Retain last approved piece and label back side Maintain a clean and safe work area, cleaning floor, machine, work area at end of each job and at end of shift Cut cores for particular jobs when needed. Obtain boxes and materials necessary for job Operate production equipment to produce good, quality product in an efficient/quality-oriented manner. Makes suggestions for ways to improve production process Works with sales and estimating to test/run samples for new product introduction Makes sure product being produced matches the spec card and the degree of quality needed (tolerances Updates spec card for future runs when process is changed Observe machine operation to detect workpiece defects or machine malfunctions; adjust machines as necessary. Change worn machine accessories such as cutting tools and brushes, using hand tools. Perform minor machine maintenance, such as oiling or cleaning machines, changing filters or adding lubricant to the Rotary press when necessary. Notify supervisors when major service is required. Other duties as assigned.

Education:

High school diploma or equivalent

  • Set Up Brake Press Operator

    1 day ago

    Grand Rapids, United States Elwood Staffing Full time

    An international manufacturer of point of purchase displays and decorative wire products is looking to add a Set-Up Break Press Operator to their team. Apply today to learn more! Company Profile. Our client is an international manufacturer of point o Press Operator, Brake Press, Press, Operator, Staffing, Production

  • Press Operator

    4 weeks ago

    Grand Rapids, United States Boyd Company Full time

    Job DescriptionEssential Duties Include: Read and understand "Change Spec. Card Procedure"Read and understand "Non-Conforming Product Procedure"Get magnets from magnet board that contains the work order information for productionLocate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructionsDetermine and...

  • Press Operator

    5 days ago

    Grand Rapids, United States Boyd Company Full time

    Job DescriptionEssential Duties Include: Read and understand "Change Spec. Card Procedure" Read and understand "Non-Conforming Product Procedure" Get magnets from magnet board that contains the work order information for production Locate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructions Determine...

  • Automatic Press Operator

    2 days ago

    Grand Rapids, United States Pridgeon & Clay Inc Full time

    Job DescriptionJob DescriptionAre you looking for a challenging yet rewarding career that allows you to utilize your skills to their fullest potential? Do you want to join a team of hardworking, enthusiastic and creative people and enjoy working with a company that recognizes and embraces diversity? Do you take pride working with a company that is committed...

  • Press Brake Operator

    2 weeks ago

    Grand Prairie, United States Skilled Craftsmen of Texas, Inc. Full time

    Job DescriptionJob DescriptionM- F2:30 PM - 11:00 PM$15-$19/HRDuties:Receive flat material.Form specific part utilizing the break press to form the contour of the material.Store material in a designated area.May utilize crane to maneuver material to be formed with the break press.This position may require working with another worker.Ability to communicate...

  • Press Brake Operator

    5 days ago

    Grand Prairie, United States Skilled Craftsmen of Texas, Inc. Full time

    Job DescriptionJob DescriptionM- F2:30 PM - 11:00 PM$15-$19/HRDuties:Receive flat material.Form specific part utilizing the break press to form the contour of the material.Store material in a designated area.May utilize crane to maneuver material to be formed with the break press.This position may require working with another worker.Ability to communicate...

  • 2nd Shift

    2 days ago

    Grand Haven, United States Automatic Spring Products Corporation Full time

    Job DescriptionJob DescriptionESSENTIAL DUTIES AND RESPONSIBILITIES include the following. Other duties may be assigned.To perform routine operation of the press(s), the auxiliary equipment, and general maintenance of the press(s).To perform all required shift start up and shift end functions.To perform all required Q.C. checks.To make minor adjustments to...

  • Processing -Machine Operator (Press Brake)

    3 weeks ago

    Grand Prairie, United States MDMartin Full time

    Job DescriptionJob DescriptionSummary: They will be operating a press brake machine to shape multiple types of metal, primarily sheet metal. To do so, the operators load pieces of metal into the machine for shaping or straightening, aligning and positioning the material to achieve specific shapes.Requirements: · Bilingual- Speak and understand English...

  • Brake Press Operator

    1 month ago

    Grand Rapids, United States Metal Components Full time

    Job DescriptionJob DescriptionMetal Components strives to be an employer of choice. Our small business creates a family feel and a career path for team members. By joining our team, you will receive compensation for your position as well as opportunities to grow. Metal Components desires candidates that have a great mindset and skillset. Please see job...

  • 2nd Shift Press Operator

    3 weeks ago

    Grand Blanc, United States VP Total Solutions Full time

    Job DescriptionJob DescriptionJob DescriptionMacArthur Corporation is a world class manufacturer of innovative labels, tags, decals, and functional filmcomponents for automotive, mobility, electronics, health technology, industrial and consumer goodssectors. Headquartered in Michigan (USA) with joint ventures in Poland and China, we service the...

  • Press Operator

    3 weeks ago

    Eaton Rapids, United States Dowding Industries Full time

    Job DescriptionJob DescriptionTitle: Press Operator Status: Full-time, Non-exemptManages Others: NoReports to: Production SupervisorTravel: NoneAbout UsSince 1965, Dowding has grown from a tool and die manufacturer to a leading edge, world-class manufacturer of metal stampings, fabrication, precision machined components, and assemblies. We capitalize on our...

  • Operations Manager

    4 weeks ago

    Grand Rapids, United States Schuler Inc. Full time

    Job DescriptionJob Description***This position is located in Hastings, MI, which is 45 min outside Grand Rapids***ResponsibilitiesEstablish and maintain business standards for accuracy, productivity and reliabilityManage the daily functions of the businessPrepare annual performance review and reevaluate processesManage budget to align with goals of...

  • Press Operator

    4 weeks ago

    Eaton Rapids, Michigan, United States Dowding Industries Full time

    Title: Press Operator Status: Full-time, Non-exempt Manages Others: No Reports to: Production Supervisor Travel: None About Us Since 1965, Dowding has grown from a tool and die manufacturer to a leading edge, world-class manufacturer of metal stampings, fabrication, precision machined components, and assemblies. We capitalize on our...

  • Press Operator

    1 month ago

    Eaton Rapids, United States Dowding Industries, Inc. Full time

    Title: Press OperatorStatus: Full-time, Non-exemptManages Others: NoReports to: Production SupervisorTravel: NoneAbout UsSince 1965, Dowding has grown from a tool and die manufacturer to a leading edge, world-class manufacturer of metal stampings, fabrication, precision machined components, and assemblies. We capitalize on our rich manufacturing history and...

  • Mold Setter

    7 days ago

    Grand Rapids, United States KENDRICK PLASTICS INC Full time

    Off shift - 2nd or 3rd shift Job Summary Responsible for the safe, quality conscious operation during set up of molding machines using established procedures and in cooperation with Supervision to ensure all presses are running efficiently, meeting all goals (i.e., scrap, efficiency). Responsible to Mold product to established standards and...

  • Tool and Die Journeyman

    2 weeks ago

    Grand Rapids, United States AIMS Advantage INC Full time

    Tool and Die Journeyman Duties Performs all in-house die polishing and bench work Maintains a preventative maintenance program on all tools. Keeps a thorough and accurate history on each tool Performs mold cleaning, lubrication, and proper mold identification to the tooling standards Maintains parting line, quality and surface polish Maintains and...

  • Machine Operator

    2 days ago

    Grand Rapids, United States Pridgeon & Clay Inc Full time

    Job DescriptionJob Description3rd Shift (10:30pm-7:00am) $1.00/Shift Differential.Objective: The Machine Operator operates various machinery to tap, ream, form, sand, spot weld and/or rivet components in an exemplary manner according to the company quality policies.Qualified candidates will possess the following Minimum Requirements:Three months experience...

  • Machine Operator

    2 days ago

    Grand Rapids, United States Pridgeon & Clay Inc Full time

    Job DescriptionJob Description2nd shift (2:30pm-10:30pm) Overtime Available $1.00/shift differential!Objective: The Machine Operator operates various machinery to tap, ream, form, sand, spot weld and/or rivet components in an exemplary manner according to the company quality policies.Qualified candidates will possess the following Minimum Requirements:Three...

  • Field Service Technician

    1 month ago

    Grand Rapids, United States Schuler Inc. Full time

    Job DescriptionJob Description****This position is actually located in Hastings, MI, which is approximately 40-45 min outside of Grand Rapids, MI**** SUMMARY OF FUNCTIONS:To assist customers with on-site trouble-shooting and repair of existing Schuler equipment or the assembly and startup of new Schuler presses, as well as customer training. Also, establish...

  • Industrial Sewing Specialist

    4 weeks ago

    Grand Rapids, Michigan, United States Tekton Full time

    As an Industrial Sewing Specialist, you will produce fabric pouches and bags used to organize, carry, and store hand tools.Mark out, cut, assemble, and sew.This includes setting up the work area; cutting the fabric, webbing, and hook-and-loop pieces; and assembling and sewing the finished goods.To offer you the broadest perspective, this might mean working...