AP Entry/Welder Operator
4 weeks ago
GENERAL JOB DESCRIPTION:
This position of AP Cold (Exit/Trim) Operator is responsible for all operating functions as listed below. Operation of the AP Cold Unit must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as outlined.
DUTIES
ESSENTIAL JOB FUNCTIONS:
1.) Check schedule of coils to be run to insure correct coil is on the line.
2.) Receive communication from entry of coil number running and observe for any defects and correct as necessary.
3.) Insure entire exit section is per work instructions.
4.) Monitor coils in line for steering and defects, correct as necessary.
5.) Insure Skin Pass Mill is operating as per work instructions.
6.) Insure all trimming activities are per work instructions and meet quality standards.
7.) Start the coil to the Coiler Reel and insert Interleaving Paper as per work instructions.
8.) Ensure that the proper paper is staged and ready for the coil
schedule.
9.) Contact Waste Water Treatment Plant Operator as necessary.
10.) Properly identify coils exiting the unit as per work instructions.
11.) Follow all prescribed safety rules.
12.) Housekeeping/maintenance work as assigned.
13.) Any other jobs as assigned.
SUPPLEMENTAL JOB FUNCTIONS:
1.) Other duties as assigned.
2.) Participation in continuous improvement programs.
QUALIFICATIONS
MINIMUM EDUCATION, SKILLS AND EXPERIENCE:
Minimum of a High School Degree or Equivalent (GED)
PHYSICAL ABILITIES REQUIRED:
1.) Mobility: Stand (stationary) - 15%, stand/walk - 45%, walking - 15%, sitting - 25%.
2.) Strength and Agility: Lifting - occ. 75, carrying - occ. 150 ft., push/pull - occ. 75, climbing - occ., balancing - occ., bending - occ., stooping - occ., crouching - occ., kneeling - occ., crawling - occ., running - occ., twisting - occ., turning - occ.
3.) Dexterity: Grasping (firm/strong), finger dexterity/handling,
1. Mobility in plant
2. Ability to lift at least 50 lbs.
3. Visual ability with or without correction
4. Communication abilities
5. Ability to work rotating shift (rotating from days to nights on a weekly or bi-weekly schedule).
HEALTH AND SAFETY
1.) Work in compliance with the Occupational Health and Safety Act and regulations.
1.) Follow Company safety rules.
2.) Report the absence of or defect in any protective equipment or clothing to the Supervisor or Manager immediately.
3.) Use or wear the equipment, protective devices or clothing that is required to be used or worn:
* Safety shoes
* Safety glasses
* Hearing protection
4.) Report to the Safety Coordinator, Group Lead or Supervisor any contravention of the Occupational Health and Safety Act and Regulations or Company policy.
5.) Must follow all Lock out Tag out (LOTO) guidelines for designated machines.
6.) Maintain a clean and safe work area.
WORK ENVIRONMENT:
1.) Work in compliance with the Occupational Health and Safety Act and regulations.
2.) Clean, well ventilated and safe work areas.
-
BA Entry/Welder Operator
2 weeks ago
Ghent, United States North American Stainless Full timeThe position of BA Entry/Welder Operator is responsible for all operating functions as listed below. Operation of the BA Unit must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as outlined.ESSENTIAL JOB FUNCTIONS:1.)...
-
BA Entry/Welder Operator
4 days ago
Ghent, United States North American Stainless Full timeThe position of BA Entry/Welder Operator is responsible for all operating functions as listed below. Operation of the BA Unit must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as outlined. ESSENTIAL JOB FUNCTIONS:1.)...
-
BA Entry/Welder Operator
2 weeks ago
Ghent, United States North American Stainless Full timeJob DescriptionJob DescriptionThe position of BA Entry/Welder Operator is responsible for all operating functions as listed below. Operation of the BA Unit must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as...
-
2nd Shift Aluminum Welder
18 hours ago
Ghent, United States ResourceMFG Full timesummary Remedy is Hiring for An Aluminum Welder right here in Jacksonville, FL located on the Southside. 2nd shift: 5:00PM- 1:30AM Monday-Friday Paying $17-$21/Hr. Depending on experience. Products Fitter/MIG Welder Job Responsibilities and Requirements Safety conscious and familiar with standard safety rules and policies Good communication and team working...
-
AP Exit Operator
1 month ago
Ghent, United States North American Stainless Full timeJob DescriptionJob DescriptionThe position of AP3 vacation coverage operator is responsible for all operating functions as listed below. Operation of the AP3 Unit must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as...
-
CM Crane Operator
4 weeks ago
Ghent, United States North American Stainless Full timeJob DescriptionJob Description all operating function of all cranes located in the Cold Mill. Operation of the crane must be understood in total with the focus of utilizing the equipment to meet all the quality and productivity goals as outlined in our quality system. All work instructions must be followed as outlined. Know potential hazards for each task by...
-
Journeyman Pipefitter
4 weeks ago
Ghent, United States Industrial Trade Services Full timeJob DescriptionJob DescriptionPipefitterGhent, KY$32 per hourFitting stainless steel pipe for tig welders. Must have at least 5 years of fitting experience.ResponsibilitiesRead and understand P&ID’s and isometric drawings to determine the scope of work, locations, quantities, and sizes of materials required.Layout, fabricate, and install pipe spools from...
-
QC Engineer
2 weeks ago
Ghent, United States North American Stainless Full timeJob DescriptionJob DescriptionGENERAL JOB DESCRIPTION:This position is responsible for providing professional quality engineering service and technical support involvingtechnical quality, in-process quality, and customer service. Supports NAS total quality program to improve cost,productivity, yields and customer requirements.The QC Engineer be involved in...